Hornby X9659 4 Pin DCC Decoder

4 pin decoder for DCC fitted 0-6-0 locomotives and the new Sentinel. A unique decoder for smaller locos with restricted space.

£14.49

Hornby R8249 8 Pin DCC Decoder

The Hornby locomotive decoders may be used with all standard digital control equipment that conforms to the NMRA standards. Control of the motor's rotational speed (load compensation). Acceleration and deceleration separately adjustable. Selectable for operation with 14, 28, 128 speed steps.

Four On/Off function outputs.Two of the function outputs are dedicated for the head / tail lights. Motor overload current protection

£20.99

Hornby R8247 Points & Accessory Decoder

The Hornby R8247 Accessory/Point Decoder can be programmed to accommodate four point motors or solenoid operated accessories, plus other electrical accessories that require a constant or delayed current flow, for example a turntable.

By adjusting the CV settings of each output a graduation of varying ‘bursts’ of current up to a constant current (turntable motor operation, lighting, etc.) can be obtained for each individual output.

£48.99

Hornby R8245 Sapphire 21 Pin Decoder

Supports 1 Amp continuous current with 1.5 Amp stall. Low speed "gear" for shunting operations.  Set amounts of "water" and "fuel" can be stored in the Sapphire providing real time fuel consumption. Burn rates can be selected.  All CVs can be changed.

The Sapphire Decoder is NMRA compliant, and supports RailCom and asymmetric DCC.

High Frequency back-emf motor control - high frequency to reduce audible noise. Low speed gear for shunting operations. 14, 28 and 128 speed steps. Operation on conventional DC layouts. Provides 1A continuous motor current and 1.5A stall. Four function outputs rated at 200mA each. Total current sum of function outputs is 500mA. Directional or independant lighting, featuring dimming and extensive special effects. Advanced consist control and extended addressing. 21-pin connector (8-pin converter supplied)

£34.99

Hornby R8242 Digital Power Clip

For connecting the R8216 Point and Accessory Decoder to the track.

£2.79

Hornby R8232 DCC Electro Point Clips

To obtain the best from the Hornby Digital system it is recommended that all points are made ‘live’ by attaching 2 x R 8232 DCC Electric Point Clips to each point.

£4.25

Hornby R8123 Class 50 TTS Sound Decoder

£41.99

Hornby R8121 Class 66 TTS Sound Decoder

£41.99

Hornby R8120 Class 43 TTS Sound Decoder

£69.99

Hornby R8115 Merchant Navy Class TTS Sound Decoder

£41.99

Hornby R8114 Black 5 TTS Sound Decoder

£41.99

Hornby R8113 Class 9F TTS Sound Decoder

£41.99

Hornby R8110 Castle Class TTS Sound Decoder

£42.99

Hornby R8104 Class 60 TTS Sound Decoder

£42.99

Hornby R8102 Class 37 TTS Sound Decoder

£41.99

Hornby R8101 Class 31 TTS Sound Decoder

£42.99

Hornby R7239 Class J36 TTS Sound Decoder

£41.99

Hornby R7143 Britannia Class TTS Sound Decoder

£41.99

Hornby R7141 Rebuilt Merchant Navy Class TTS Sound Decoder

£42.99

Hornby R7140 Class 43 Valenta TTS Sound Decoder

£69.99

Bachmann 36-569 Class 90 Decoder

£39.95

Bachmann 36-568A 6 Pin Decoder

6 Pin DCC Loco-Decoder with Back EMF featuring Railcom

£29.95

Bachmann 36-567 Next 18 Decoder

£21.95

Bachmann 36-563 6 Pin to 8 Pin Plug

6 Pin Decoder Socket with 8 Pin Plug (x3)

£13.95

Bachmann 36-562 6 Pin Wriring Harness

6 Pin Decoder Socket with Wiring Harness (x3)

£9.95

Bachmann 36-561 Dynamis Points Decoder

£46.35

Bachmann 36-557 21 Pin Decoder

E-Z Command 1 Amp 4 Func. 21 Pin DCC Decoder (DC Compatible)

£21.95

Bachmann 36-556RA 6 Pin Decoder

E-Z Command 90° 6 Pin DCC Decoder (DC Compatible) + Back EMF

£17.95

Gaugemaster Seep GMC-PM20D Surface Mounted Point Motor (DCC-Fitted)

Designed with easy installation in mind, PM20D is placed parallel to your point-work and operates equally well orientated either way. PM20D works well with all popular modelling scales, and with the leading brands of track in the UK.

The magnetic coils are high-efficiency for reliable operation, needing much less current than most other brands. PM20D also has a plug-in harness that is very easy to use. Mounting screws are included.

£18.95

Gaugemaster Seep GMC-PM10D Classic Solenoid Point Motor (DCC-Fitted)

The PM10D point motor has been created to make installation and wiring as easy as possible for all modellers in all scales.

£18.95

Gaugemaster GM782 Station (Modern) Scenic Sounds Module

Features:

•     Compact sound module with built-in loudspeaker
•     Real natural sounds specially recorded for these modules
•     Easy connections - just two screw terminals for power supply
•     Power from 8-16v smooth DC for natural random sounds
•     Or power from DCC for controlling sounds by DCC or random
•     Fits inside a model or under the baseboard
•     Built-in adjustable volume control
•     Joint British development between Gaugemaster and Train-Tech

When powered by DC:

Modules play an appropriate background sound with individual sounds played in randomly.

When powered by DCC:

Modules can play randomly as above, or individual sounds can be played on command by DCC; e.g.Point throw played as a point changes, signal rodding etc.

Sounds on this module include:

•     Door closing beeps
•     Guard's whistle
•     Trains pulling out
•     General station noise

£29.95

Gaugemaster DCC18 OMNI Next18 Decoder

This decoder is for use with locomotives that have Next18 sockets..

£21.95

Gaugemaster DCC22 Classic 8 Pin Micro Decoder

This decoder is best suited for HO/OO locomotives. It comes complete with a fitted harness linking to a 8 pin plug.

£27.95

Gaugemaster DCC23 Classic 6 Pin Decoder

Most suited to N Gauge locomotives. This decoder can be used for some HO/OO locomotives.

£27.95

Gaugemaster DCC26 Compact 8 Pin Decoder

Most suited to N Gauge locomotives. This decoder can be used for some HO/OO locomotives.

£16.95

Gaugemaster DCC28 OMNI 6 Pin Decoder with Harness

6 Pin decoder with plug-able 8 pin harness. This very versatile 2 function decoder is very small so it can fit in most locomotives regardless of space.

£20.95

Gaugemaster DCC29 OMNI 8 Pin Direct Plug Decoder

8 Pin, 4 function decoder.

£19.95

Gaugemaster DCC30 Prodigy DCC Accessory Decoder for Four Accessories

This 3 amp stationary decoder has four separately addressed outputs which can be used individually or set up as a route. This decoder is used for the operation of solenoid point motors or accessories such as lighting or signals.

£64.95

Gaugemaster DCC72 8 to 21 Pin Adaptor

£4.95

Gaugemaster DCC80 DCC Autofrog

The DCC80 Autofrog is a simple switch that automatically changes the frog polarity on your DCC layout. In most situations, the use of electrofrog points is recommended on digital layouts to ensure reliability but this can make extra switching more complicated than it needs to be. Allow us to introduce you to the Autofrog. Wiring the DCC80 is simple. There are three solder connections on the board, 2 connections labelled “R” - which you should connect to your rails or your bus and 1 connection labelled “F” which you connect to the frog input wire.

£5.95

Peco PLS-135 Smartswitch Stationary Decoder

The Smartswitch system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Stationary Decoder provides an interface between a Smartswitch Control Board and a DCC control system to enable the operation of turnouts, semaphore signals, crossing gates etc through a DCC controller.

£17.50

DCC Concepts DCD-ZN6D Loco Decoder

Zen 6 Pin Direct plug-in decoder with stay alive unit

The decoder offers slow running characteristics and as it is the smallest decoder in the range you will always find places to house it.

Decoder Size - •Length: 13.5mm •Width: 8.5mm •Depth: 3mm

Motor drive rating 750mA/1amp, 2 Functions.

Each - £26.95

5 Pack - £119.95 (to order)

DCC Concepts DCD-ZN68 Loco Decoder

ZEN 6 PIN VERSATILE 2 Function Decoder with Stay Alive.

Much like its "bigger brothers" the N68 decoders have very smooth motor drive characteristics which allow for slow speed running even inside N scale locomotives.

These decoders are small enough to fit in any N scale locomotive and with the included 6 pin & 8 pin harnesses you can use them on OO/HO scale locos as well.

Decoder Size - •Length: 13.5mm •Width: 8.5mm •Depth: 3mm

Motor drive rating 750mA/1amp, 2 Functions.

Each - £29.95

5 Pack - £134.95 (to order)

DCC Concepts DCD-ZN8D Loco Decoder

ZEN NANO 8 Pin Direct 4 Function Decoder with Stay Alive.

The smallest 8 pin direct plug decoder in the range. This decoder is smaller than most blanking plates so fitting it into a locomotive will be very easy.

Decoder Size - •Length: 15mm •Width: 7mm •Depth: 5mm

Motor drive rating 750mA/1amp, 4 Functions.

Each - £29.95

5 Pack - £134.95 (to order)

DCC Concepts DCD-ZN8H Loco Decoder

ZEN NANO 8 Pin Wired 2 Function Decoder with Stay Alive.

One of the smallest decoders produced by DCC Concepts. This decoder is only 15mm long so it can be hidden inside any locomotive either steam, diesel or electric.

Decoder Size - •Length: 15mm •Width: 7mm •Depth: 5mm

Motor drive rating 750mA/1amp, 2 Functions.

Each - £29.95

5 Pack - £134.95 (to order)

DCC Concepts DCD-Z360 Loco Decoder

ZEN 360 8 Pin Direct 4 Function Decoder with Stay Alive

The Zen 360 decoder has been developed to fit in almost any OO/HO locomotive irrespective of DCC socket orientation. As long as your locomotive has an 8 pin socket, this decoder will fit. This decoder has been designed with a twin PCB stacked one on top of the other so you only need to plug it in as it will fit in place of the original blanking plate.

Decoder Size - •Length: 14.5mm •Width: 12.5mm •Depth: 3.5mm

Motor drive rating 750mA/1amp, 4 Functions.

Each - £26.95

5 Pack - £119.95 (to order)

DCC Concepts DCD-Z218 Loco Decoder

ZEN 218 21 & 8 Pin 4 Function Decoder with Stay Alive.

The Zen 218 decoder is a very versatile decoder which takes away the choice of which decoder to buy for your new locomotive as it comes complete with both 21 and 8 pin plugs. Due to its size will fit in most OO/HO scale locomotives.

Decoder Size - •Length: 22mm •Width: 16mm •Depth: 5mm.

Harness length 75mm.

Motor drive rating 750mA/1amp, 4 Functions.

Each - £26.95

5 Pack - £119.95 (to order)

DCC Concepts DCP-CB1 Cobalt Omega

COBALT Omega Slow Action Analogue Point Motor.

Supplied complete including the mounting screws and the very popular double-sided foam mounting pads so there is nothing else needed!

Cobalt Classic Ω has been totally re-engineered on the inside to make it quieter and even more durable with added features too:

Now the throw-bar is pre-centred and ready to install, no soldering thanks to its spring connectors, switchable power supply range 7 to 18v and THREE switches, each switch is directly linked to the movement of the throw-bar for absolute confirmation of point changing.

Typical power requirement 20mA. Can be converted to Digital with the AD series of decoders.

Each - £16.95, - - 6 Pack - £94.95 (to order) - - 12 Pack - £184.95 (to order)

DCC Concepts DCP-CB1ip Cobalt ip Analogue

COBALT ip Slow Action Analogue Point Motor.

Supplied complete including the mounting screws and the very popular double-sided foam mounting pads so there is nothing else needed!

While Cobalt-iP may look almost the same on the outside, it has a totally new and even quieter internal gearing structure, re-designed internal electronics to add actively managed drive speed and at the same time, added an all new microprocessor-controlled “intelligent power” system to make Cobalt-iP perform better than any point motor you have ever seen. :

The throw-bar is pre-centred and ready to install, no soldering thanks to its spring connectors, power supply range 7 to 18v and THREE switches only operating if the point has REALLY changed, a direction reverse switch.

Standby power 5mA operating power 50mA (typical). Can be converted to Digital with the AD series of decoders.

Each - £18.95, - - 6 Pack - £109.95 (to order) - - 12 Pack - £199.95 (to order)

DCC Concepts DCP-CB1Dip Cobalt ip Digital

COBALT ip Slow Action Digital (DCC on-board) Point Motor.

Supplied complete including the mounting screws and the very popular double-sided foam mounting pads so there is nothing else needed!

Digital fitted version of the Cobalt-iP, with the samegearing structure, microprocessor-controlled “intelligent power” system to make Cobalt-iP perform better than any point motor you have ever seen.

The throw-bar is pre-centred and ready to install, no soldering thanks to its spring connectors, power supply range 7 to 18v and TWO switches only operating if the point has REALLY changed, auto centering and direction reverse software.

Standby power 5mA operating power 50mA (typical). Digital Fitted - decoder not required.

Each - £21.95, - - 6 Pack - £124.95 (to order) - - 12 Pack - £244.95 (to order)